Mauser M1996 (NR od 12000)

Sub Categories

One Piece Pivot Mounts

About the Mauser

Back in 1811, Friedrich I of Wurttemberg launched an arms factory in Oberndorf, Germany. Employing 133 workers, the company officially started its business in the following year serving as the royal weapon forge. The initial moderate success of the company was refined in 1867 when Wilhelm and Paul Mauser came up with an innovative rotating bolt system used for breechloading rifles. Most of their rifles at the time were built around a 7.9x57J cartridge which eventually became known as the 8mm German cartridge.

Alongside the Model 93 release, the smaller, 7x57mm cartridge was introduced. The United States spotted the potential of German ingenuity; hence they incorporated many features of Mauser design into their 1903 Springfield and so did the United Kingdom with their SMLE rifle that was the standard of British infantry units up until the 1950s. Soon after, many countries around the world, such as Turkey, Brazil, South Africa, Iran, Sweden and even China had recognised the outstanding performance of Mauser 93 and began flooding the company with new orders.

Along with their rifle production success, Mauser also broke new ground in 1896 with the introduction of their autoloading C96 pistol that was produced up until 1936. In 1897 the Mauser family were given control over the factory and renamed it Waffenfabrik Mauser AG. Only a year later, one of the most recognisable Mauser rifles of all time was presented by the company – Mauser Gewehr 98. The rifle had been redesigned with some of the noticeable changes being better-ruptured case gas venting, a stronger receiver with a larger receiver ring and an extra third locking lug providing additional safety. In later years, numerous rifles were derived from the original Gewehr 98 design, a lot of them being manufactured by various German contractors.

In the first decades of the 20th century, Mauser introduced a myriad of hunting rifles such as Type A, Model B, Model K, Armee-Model C and Africa Model. Up until the 1960s, various other models were presented including M1916, Mauser 1925 Special range, Karabiner K98, Mauser KKW cadet rifle, Gewehr 41 etc. Alongside their rifle production, the company additionally focused on the production of hand and pocket pistols, with some of the most recognizable models being Mauser 1910, Mauser 1914, Model 1934, and Mauser HSc.

After World War II, when the company was seized by Allied forces and placed under French control, the factory was torn down, and its records were destroyed. The former Mauser engineers Edmund Heckler and Theodor Koch, together with their associate Aled Seidel founded Heckler and Koch arms firm in the following years, recovering some leftovers of Mauser company which remained in the arms of Allied forces until 1952 when it was again permitted to continue manufacturing firearms. In the second half of the 20th century, the company presented some new models such as Model 66, Model 77, Model 86SR, Mauser SP66, Models 94 and 96, Mauser SR 97, Mauser 90SA and Mauser 90DA.

The Rheinmetall Berlin AG bought the firearms division of the company in 1996 and renamed it to Mauser-Werke Oberndorf Waffensysteme GmbH. In 1999, part of the Mauser was sold to Schweizerische Industrie Gesellschaft company often referred to as SIG, which later became known as Mauser Jagdwaffen GmbH.

Today, the company is under the parentage of the Blaser Group, which also manufactures rifles under the J.P. Sauer & Sohn brand. Mauser has presented some new models in the last few years, such as Mauser M03, M12, and M18, attesting to the company’s rich and successful history once again.

Mauser M1996 (serial number higher than 12000) Rifle Review

Not to be confused with an older version of Mauser M96 (Swedish Mauser), the M1996 is a straight-pull rifle introduced by Mauser in 1996. The company entered the straight-pull market with this model; however, it did not get a great amount of attention at the time. Eventually, Roessler had bought the patent and the rights to Mauser M1996 and created their version of the rifle which they renamed Roessler Titan 16. The production of M1996, as well as the successor M97, was stopped and Roessler took over the production with the Titan rifle which is still manufactured up to this day. Both weapons share most of their properties.

Contrary to M97 which uses a cocking slide mechanism, Mauser M1996 comes with a tang style three position safety. The rifle is available in both – single and double row magazines holding up to five cartridges whereas the M97 only comes with a single row magazine. The shape of the stock is different as well as the upper part of the buttstock is straight compared to the M97 model.

Mauser M1996 features a front locking system with sixteen locking lugs that lock up safely into the barrel of the rifle. Another interesting design feature is the bolt handle which is positioned at the front of the bolt allowing for the user’s shoulder to push the rifle forward when reaching for the grip. Made from high-quality carbonitrided steel, the receiver comes with five holes for mounting purposes. The single-stage trigger is pre-set at the factory for a comfortable pull weight of 2268g (5lbs).

All models with a serial number higher than 12000 come with a lower height difference between the mounting surfaces (BHU) and increased B distance between the holes on the receiver.

The possible barrel length for Mauser M1996 is 572 mm (22½-inch).

Mauser M1996, chambered for .30-06 Spr.

Figure 1: Mauser M1996, chambered for .30-06 Spr. (Source: https://www.lot-art.com/auction-lots/MAUSER-M-1996-cal-30-06-96006662/1793143-mauser_m_1996-02.8.21-mauritz)

Mauser M1996 can be chambered for the following calibres:

.243 Win.
.25-06 Rem.
.270 Win.
7mm Rem. Mag.
7x64
.300 Win. Mag.
.308 Win.
.30-06 Spr.
9.3x62

The rifle is available in the following variants:

Maser M1996 Premium
Mauser M1996 Stainless

All Mauser M1996 receivers come with five holes for mounting purposes, two at the front and three at the rear mounting surface.

Mauser M1996, chambered for .30-06 Spr.

Unfortunately, we were unable to find a picture of the Mauser M1996 bare mounting surface. The receiver shown in the picture above is that of a Roessler Titan 16, as the rifles are essentially the same. Should you happen to own a Mauser M1996 and would be willing to send us some photos of the mounting surface without mounts, please contact us. We kindly thank you for your help.

Please note that all models with a serial number higher than 12000 come with a lower height difference between the mounting surfaces (BHU) and increased B distance between the holes on the receiver.

A1: /

A: 21.9 mm

B: 114 mm

C: 15.3 mm

C1: 15.3 mm

BHU: 2 mm

Ø: 6-48

R1: R51

R2: R17

Which Rifles Have Interchangeable Mounts

Two-piece mounts

All the rifles listed in the category below have two-piece mounts interchangeable with Mauser M1996. To meet interchangeability conditions, two-piece mounts must match in all dimensions except the B distance. B distance can vary because two-piece mounts can be installed and adjusted closer or further apart. Rifles that meet such criteria are:

Roessler Titan 16
Mauser M97

One-piece mounts

All the rifles listed in the category below have one-piece mounts interchangeable with Mauser M1996. For one-piece mounts to fit on a rifle, mounting surfaces on these rifles must match in every dimension. Rifles that share the same dimensions and mounting surface with Mauser M1996 are:

Roessler Titan 16

Our Recommendations for Mounts

Picatinny Rails

Picatinny rails are one of the most versatile mounting solutions on the market as they offer numerous mounting choices. This Picatinny rail produced by the German company EAW is made of steel and comes with a thirty-year warranty. It will fit perfectly on the receiver of Mauser M1996.

Help Us Build Our Riflescope Mounts Database

If you happen to own this or any other rifle, we would appreciate it if you could help us expand our database by sending us some photos of the rifle receiver (the bare mounting surface of the rifle without the mounts installed). For your help, our company offers a fair return in terms of practical rewards.

Please send us an email for more information. You can contact us here: info@optics-trade.eu

Ask for price

View Product

Add to compare

Filters

Sort

VIDEO

Pivot mounts are a special kind of repeatable mounts that are especially popular in Europe and mainly produced by European manufacturers. Most notable among them are German Companies like EAW (Ernst Apel Wurzburg), Recknagel, Henneberger and MAK. These Companies were also among the first to produce mounts of this type. Non German companies like Rusan are also following this trend.

Main benefits of pivot mounts, or swing mounts as they are sometimes called are:

100% repeatability,
very quick and easy detaching and reattaching,
extremely durable; most mounts of this kind are tested on 10000 or more reattachments,
size and weight; light and small, elegant.

There are also some minor weaknesses that such mounts posses and they are: they are usually more expensive than other types of mounts, the installation on the rifle should be done by a skilled gunsmith and most of these mounts are higher than 14 mm.

A distinct feature of pivot/swing mounts is the way the scope attaches to the rifle. The front foot of the mount on the scope is inserted in the front base under a 90 degrees angle to the barrel. Then the entire scope is pivoted around the front base until it is locked into position by the rear base.

Pivot mounts of all types enable windage correction on the rear base at the time of the mounts installation. There are three main types of pivot mounts which are distinguished by the type of the rear base:

EAW style rear base: produced by EAW and Rusan,
Dovetail rail base: produced by Recknagel, Henneberger, MAK and others.
Leupold type rear base

Different Types of Pivot Mounts

Mauser M1996 (NR od 12000)

Sub Categories

About the Mauser

Mauser M1996 (serial number higher than 12000) Rifle Review

Mauser M1996 can be chambered for the following calibres:

The rifle is available in the following variants:

Which Rifles Have Interchangeable Mounts

Two-piece mounts

One-piece mounts

Our Recommendations for Mounts

Picatinny Rails

Help Us Build Our Riflescope Mounts Database

INNOmount Zeiss ZM/VM Rail Pivot Mount, Mauser 97

INNOmount Pulsar Trail2 Pivot Mount, Mauser 97

INNOmount Picatinny Pivot Mount, Mauser 97

INNOmount Picatinny Pivot Mount, Roessler Titan 16

INNOmount Guide TS450 Pivot Mount, Mauser 97

INNOmount Guide TS450 Pivot Mount, Roessler Titan 16

INNOmount TVT-Archer Pivot Mount, Mauser 97

INNOmount TVT-Archer Pivot Mount, Roessler Titan 16

INNOmount TVT-Archer Pivot Mount, Roessler Titan 3/6

INNOmount Pulsar APEX Pivot Mount, Mauser 97

INNOmount Pulsar Thermion Pivot Mount, Mauser 97

INNOmount Swarovski SR Rail Pivot Mount, Mauser 97

VIDEO

Payment methods

Shipping methods

Shopping

Contact us

Certificates

Follow us on

FAQ and Media

Mauser M1996 (NR od 12000)

Sub Categories

About the Mauser

Mauser M1996 (serial number higher than 12000) Rifle Review

Mauser M1996 can be chambered for the following calibres:

The rifle is available in the following variants:

Which Rifles Have Interchangeable Mounts

Two-piece mounts

One-piece mounts

Our Recommendations for Mounts

Picatinny Rails

Help Us Build Our Riflescope Mounts Database

VIDEO

Your wishlist