35mm Scope Rings

General features of scope rings

35mm scope rings and mono-block mounts are usually very wide, with at least 20mm width. This way there is a huge contact surface between the scopes and the mounts.

The size of 35mm main tube is a rarity, a kind of compromise done by only a couple of companies: the Romanian IOR and the USA-based Vortex and Leupold. Why did they choose to use this diameter is a mystery by itself. Especially in a time when all other rifle scope manufacturers are producing scopes of the same Category with 34mm tubes. Due to this reason, there are only a couple of manufacturers of mounts that produce mounts with this diameter. Almost all mounts for such scopes are of tactical nature, either in the form of tactical scope rings or tactical mono-block mounts.

The most well-known brands of mounts of this diameter are:

35mm Scope Rings

Contessa 35mm Scope mount

The most important thing when mounting a rifle scope with rings is to be aware of the torque needed to fasten the screws in the scope rings. Go over the limit and the structural integrity of the rifle scope will be compromised. Scope rings can also leave a visible mark if not tightened accordingly. The amount of torque should not exceed 2.2 Nm

Is lapping of the 35mm scope rings really needed?

Lapping is a process that is essentially lining two mounting rings perfectly to one-a-another. It is done with special cylinders that grind off the excess metal.

When the ring is constructed from two near half circles - so if the circle of the ring is split in half, roughly in the ratio 50:50 and such riflescope rings are mounted on two separate mounting bases, then lapping is recommended. If lapping is not performed, the very small offsetting can be present when all the different pieces of the mount come together and when both scope rings are mounted on two separated bases. If the mounting of two high-quality scope rings is done on a single-piece base, then lapping is not needed. This is one of the reasons that Picatinny rails are becoming so popular in recent years.

In the worst-case scenario, the axis that runs through the center of the rear scope ring does not completely match the axis that runs through the center of the front ring. For this reason, the scope, if mounted into such rings is under unwanted structural stress. The most obvious problems that occur due to this reason are less than perfect optical performance, tracking problems, the side focus mechanism can stop working and the point of impact groups can be dispersed.

Accessories and tools for lapping 35mm scope mount

With 35mm scope mount, there is also quite problematic to get suitable lapping tools, since most of them are produced in 30 and 34mm diameters. It is a good idea to use a ribbon cut from latex/rubber gloves on the lower contact surface in the ring.

Scope mounts that don't need lapping

Lapping is also not required with monoblock mounts and all mounts are made from one piece of material and alignment of both scope rings is usually perfect. Lapping is also not required with high-quality European mounts since their tolerances are minimal.

Compatibility Below

Filters

Sort

Rusan Q-R mount for Blaser, 35 mm

As low as $269.00

View Product

Add to compare

Filters

Sort

VIDEO

Blaser has revolutionised the way rifle scopes are mounted on the rifles with their saddle mount system. The main feature of this system is that it can be found with all Blaser rifles, no matter what type or model they are. That means that Blaser succeeded to offer the same mounting solution on repeating rifles like on the R93, R8, Combination rifles like B95/97, Single Shot break rifles like K95, Drillings like D99, Bockdrillings like D14, side by side rifles like S2 and all other rifles made by Blaser.

This system is thus by far the most versatile mounting system on the market. Additional advantages that it offers are:

Very low mounting height of scopes with rails like Zeiss ZM/VM, Swarovski SR, S&B Convex,
100% repeatability when detached and reattached,
small size and weight,
easy detaching and reattaching the scope to a rifle.

This mounting system has four notches for mounting directly on the barrel and not on the action. All mounts that attached to all four notches can be used on all types of Blaser rifles. Those mounts however that are attached only to 2 notches (most commonly these are mounting solutions for the red dot sights and reflex sights) are rifle specific. That means that MAKnetic for Docter Sight for Blaser R8 will not fit on any other Blaser rifle except R8. Such mounts are very elegant due to their small size but their versatility is limited to one specified type of Blaser rifle only.

Another important consideration that needs to be pointed out is that all mounts for Blaser rifles (original and non-original) are designed to work only on one single barrel. That means that if you have set a mount on one barrel (setting a mount on the Blaser rifle means to tighten the adjustment screw in a way that clamping of the mount on the four notches is done by exactly appropriate force) it will work only on that Blaser barrel and not on others. You can have multiple optics on one Blaser barrel but you cannot have a single optics on multiple Blaser barrel. The only exception to this rule are Dentler mounts.

This mounting system can be found on the following Blaser rifles:

R8
R93
B95/B97
D99
K95
S2

35mm Scope Rings

General features of scope rings

Is lapping of the 35mm scope rings really needed?

Accessories and tools for lapping 35mm scope mount

Scope mounts that don't need lapping

Rusan Q-R mount for Blaser, 35 mm

VIDEO

Payment methods

Shipping methods

Shopping

Contact us

Certificates

Follow us on

FAQ and Media

35mm Scope Rings

General features of scope rings

Is lapping of the 35mm scope rings really needed?

Accessories and tools for lapping 35mm scope mount

Scope mounts that don't need lapping

Rusan Q-R mount for Blaser, 35 mm

VIDEO

Your wishlist