Kepplinger Repetierer

Sub Categories

Mounts

Kepplinger Repetierer Rifle Review

The Kepplinger Repetierer is a bolt-action rifle designed by Hannes Kepplinger, who has previously worked for Steyr and was one of the designers who modified the Barnitzke system, leading to the development of the Steyr GB/Pi18/GB-8. The Repetierer/Jägerbüchse rifle was developed in the 1980s in Kufstein.

The rifle features a bolt with three locking lugs, an interchangeable barrel and blued receiver, fixed sight, a Bavarian cheekpiece, and a rubber recoil pad at the rear end of the wooden walnut stock. It is a typical west-European hunting rifle design with a chamber diameter similar to the one on Voere Titan. The detachable plastic magazine can hold up to 5 cartridges and can be removed by a push of a button located at the lower end of the forearm. There is a safety lever positioned on the right side of the receiver behind the bolt handle which blocks the trigger and firing pin. The rifle uses Kepplinger set trigger, also known as Frankonia set.

Although the production of various variants and a greater number of models was initially planned, the Kepplinger Repetierer rifle was distributed through Kettner only for a relatively short period.

Kepplinger Repetierer, chambered for .243 Win.

Figure 1: Kepplinger Repetierer rifle, chambered for .243 Win. (Source: https://www.waffengebraucht.at/waffen/kugelrepetierer/kepplinger-kufstein-im-kaliber-243win-mit-leupold-vari-x-iii-25-8-fach-und-absehen-4--462508)

Kepplinger Repetierer Calibers

The rifle is available in the following calibers:

.222 Rem.
.223 Rem.
5.6x50
5.6x57
.243 Win.
6.5x64 Brenneke
.270 Win.
7x64 Brenneke
.308 Win.
7.5x55 Swiss
.30-06 Spr.
8x64 S

Kepplinger Repetierer comes with four holes on the top of the receiver which can be used for scope mounting purposes. There are two holes on the front and two on the rear mounting surface.

Kepplinger Repetierer receiver, chambered for .30-06 Spr.

Figure 2: The receiver of Kepplinger Repetierer rifle, chambered for .30-06 Spr. (Source: https://www.egun.de/market/item.php?id=18994831#img)

Unfortunately, we were not able to find a photo of a bare mounting surface for this rifle (no scope mounts installed). Should you happen to own the Kepplinger Repetierer, we would greatly appreciate it if you could send us some photos of the receiver without scope mounts or bases installed. You can contact us anytime at info@optics-trade.eu

Thank you for your help!

A: 21.9 mm

B: /

C: 12.7 mm

BHU: 3 mm

Ø: M3.5

R1: R14/30°

R2: R16,5

Scope Mounts Interchangeable With Kepplinger Repetierer

Rifles That Have One-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

All the rifles listed in the category below have one-piece mounts interchangeable with Kepplinger Repetierer. For one-piece mounts to fit on a rifle, mounting surfaces on these rifles must match in every dimension.

Rifles That Have Two-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

All the rifles listed in the category below have two-piece mounts interchangeable with Kepplinger Repetierer. To meet interchangeability conditions, two-piece mounts must match in all dimensions except the B distance. B distance can vary because two-piece mounts can be installed and adjusted closer or further apart.

Unfortunately, we were unable to find the B distance of the mounting holes and thus cannot provide you with the list of interchangeable scope mounts. Should you happen to own this rifle and would be willing to share with us the exact distance between inner holes (B) as well as some photos of the bare mounting surface, please contact us at info@optics-trade.eu

Your help is greatly appreciated.

Best Scope Mounts for Kepplinger Repetierer

Detachable Repeatable Scope Mounts for Kepplinger Repetierer

This Picatinny Pivot mount is made in Germany by the company INNOMOUNT. It is built from high-quality aluminum and comes with a 2-year warranty.

Help Us Build Our Riflescope Mounts Database

If you happen to own this or any other rifle, we would appreciate it if you could help us expand our database by sending us some photos of the rifle receiver (the bare mounting surface of the rifle without the scope mounts installed). For your help, our company offers a fair return in terms of practical rewards.

Please send us an email for more information. You can contact us here: info@optics-trade.eu

Filters

Sort

INNOmount TVT-Archer Pivot Mount, Kepplinger Repetierer

Ask for price

View Product

Add to compare

Filters

Sort

Kepplinger Repetierer

Sub Categories

Kepplinger Repetierer Rifle Review

Kepplinger Repetierer Calibers

Scope Mounts Interchangeable With Kepplinger Repetierer

Rifles That Have One-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

Rifles That Have Two-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

Best Scope Mounts for Kepplinger Repetierer

Detachable Repeatable Scope Mounts for Kepplinger Repetierer

Help Us Build Our Riflescope Mounts Database

INNOmount TVT-Archer Pivot Mount, Kepplinger Repetierer

Payment methods

Shipping methods

Shopping

Contact us

Certificates

Follow us on

FAQ and Media

Kepplinger Repetierer

Sub Categories

Kepplinger Repetierer Rifle Review

Kepplinger Repetierer Calibers

Scope Mounts Interchangeable With Kepplinger Repetierer

Rifles That Have One-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

Rifles That Have Two-Piece Scope Mounts Interchangeable With Kepplinger Repetierer

Best Scope Mounts for Kepplinger Repetierer

Detachable Repeatable Scope Mounts for Kepplinger Repetierer

Help Us Build Our Riflescope Mounts Database

INNOmount TVT-Archer Pivot Mount, Kepplinger Repetierer

Your wishlist